10 DSL • Acceso verde fisso quando il modem è correttamente sincronizzato con il DSLAM. • Lampeggiante durante la fase di sincronizzazione. Intern
11 USB Connettere il modem USB 3G. Console Connettere il cavo RS232 fornito alla porta seriale (9 pin) del PC. Tale connessione è opzionale. WPS Pre
12 1.4 Cablaggio WebShare 3G 244 WN è dotato di una doppia interfaccia di connessione ADSL2+/3G; ognuna di esse può essere attivata come connessione
13 1.4.2 Connessione Single WAN 3G In questa modalità, WebShare 3G 244WN viene collegato ad un modem USB 3G (HSDPA/GPRS) e configurato come un Route
14 1.4.3 Connessione Dual WAN ADSL/3G con backup In questa modalità operativa, il WebShare 3G 244WN utilizzerà la connessione ADSL come principale
15 Si ricorda che questa modalità è disponibile solo nel caso in cui la connessione ADSL sia selezionata come connessione primaria; difatti, nel ca
16 Al termine delle operazioni di cablaggio fisico del prodotto, sarà possible avviare lo stesso mediante il pulsante POWER. All’avvio, il dispositi
17 1.5 Settaggi di Default Prima di iniziare la configurazione del WebShare 3G 244WN è necessario conoscere i parametri impostati in fase di produz
18 5. Selezionare l’opzione Obtain an IP address automatically e successivamente Obtain DNS server address automatically. 6. Premere su OK per te
19 2. Configurazione Router Accedere col browser web al seguente indirizzo IP che di default è: 192.168.1.254. Premere il tasto invio. Utilizzare
ITALIANO Questo prodotto è coperto da garanzia Atlantis Land
20 • Advanced (per passare alla modalità di gestione completa) • Status • Quick Start (Per una configurazione rapida) • WAN (configurazione dell
21 2.1 Configurazione Single WAN ADSL Dopo aver verificato la correttezza del cablaggio (per ulteriori approfondimenti, fare riferimento al paragraf
22 PPPoE/PPPoA Configurare il WebShare 3G 244WN come da figura, inserendo nei campi relativi le credenziali di accesso (Username, Password) fornit
23 MPOA (RFC 1483) Questa configurazione è valida nel caso di abbonamento con 1 IP statico e NAT attivo (per la gestione della classe pubblica far
24 2.2 Configurazione Single WAN 3G 1. Impostare il campo Connect Mode in 3G per impostare l’interfaccia 3G come connessione primaria verso la rete
25 VODAFONE Per la configurazione dell’interfaccia per l’utilizzo con modem 3G Vodafone, configurare il WebShare 3G 244WN come riportato in figura
26 TIM (Telecom Italia Mobile) Per la configurazione dell’interfaccia per l’utilizzo con modem 3G TIM, configurare il WebShare 3G 244WN come ripor
27 WIND Per la configurazione dell’interfaccia per l’utilizzo con modem 3G WIND, configurare il WebShare 3G 244WN come riportato in figura. Nel
28 TRE (H3G) Per la configurazione dell’interfaccia per l’utilizzo con modem 3G TRE, configurare il WebShare 3G 244WN come riportato in figura.
29 2.3 Configurazione Wireless Configurare ora i parametri relative alla rete wireless, impostando nel campo SSID il nome da assegnare alla rete (è
3 ITALIANO 1. Panoramica di prodotto ... 8 1.1 Contenuto della c
30 2.4 Salvataggio delle impostazioni Al termine della configurazione guidata, il prodotto provvederà al salvataggio dei parametri nella memoria FLA
31 3. Supporto Offerto Per qualunque altro problema o dubbio sul funzionamento (chiamare preventivamente l’ISP per conoscere TUTTI i dettagli relati
32 Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whet
33 CE Mark Warning In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate mea
34 Outdoor 2400-24542454-2483,5 100mW(20dBm)10mW(10dBm) Italy(IT): For more info, consult the website www.comunicazioni.it Luxembourg: General auth
35 thereby providing potential future problems for the environment and human health. Moreover, it will be possible to reuse and recycle some parts
36 For more detailed instructions on configuring and using the WebShare 3G 244WN, please refer to the online manual. 1. Product Overview
37 1.2 The Front Panel LEDs LED MEANING Power • Lit when power turns ON. • Lit in red means POST (Power On Self Test) failure (non-bootable)
38 Internet • Lit red when WAN port fails to get IP address. • Lit green when WAN port gets IP address successfully. • Flashing green when IP tra
39 WPS Push WPS button to trigger Wi-Fi Protected Setup function. Reset To be sure the device is being turned on Æ press RESET button for: • 1-3 s
4 AVVERTENZE Abbiamo fatto di tutto al fine di evitare che nel testo, nelle immagini e nelle tabelle presenti in questo manuale, nel software e nel
40 1.4 Cabling WebShare 3G 244WN can be set in 3 difference mode: ADSL only, 3G only or ADSL main with 3G backup. 1.4.1 Single WAN ADSL In this mode
41 1.4.2 Single WAN 3G In this mode, WebShare 3G 244WN works using an external 3G USB modem to connect the LAN to Internet. Follow the followings st
42 1.4.3 Dual WAN ADSL/3G with backup mode In this mode, WebShare 3G 244WN works using ADSL as main connection. In case of failover of the main conn
43 1.4.4 Cabling the LAN connection In this mode, WebShare 3G 244WN can be connected to an existing LAN or can be use to create a new local area net
44 1.5 Default Settings Before configuring your, you need to know the following default settings: • Username: admin • Password: atlantis • LAN IP
45 1.6 IE Configuration Now open IE, go to Instruments menu, select the Connections tab and select one of the following options: • Never use remote
46 2. Click Manage Network connections then double-click Local Area Connection. Click Properties. 3. Click Continue (Windows needs your permissi
47 2. Browser configuration Open the web browser, enter the local port IP address of this WebShare Wireless ADSL2+ Router, which default a
48 • WLAN (for Wireless configuration) Click on the desired item to expand the page with all settings in the main navigation panel. Following next
49 PPPoE/PPPoA Set the PPP Connection as ones as the picture and insert the username and password provided by ISP. The same configuration can be
5 CE Mark Warning In un ambiente domestico il dispositivo può causare interferenze radio, in questo caso è opportuno prendere le adeguate contromis
50 MPOA (RFC 1483) Set the connection as ones as the picture and insert the IP address, Netmask and Gateway provided by ISP. IPoA/PURE BRIDGE/M
51 2.2 Single WAN 3G Configuration 1. Select 3G from Connect Mode drop-down menu and click Continue. 2. Select the connection method using Mod
52 2.3 Wireless Configuration In this section, is possible to set a new SSID for the wireless network and edit the default WPA Passphrase for the We
53 3. Support For technical questions and support, please contact our help-desk by ticket on http://www.atlantis-land.com/ita/supporto.php. For gen
54 APPENDIX A: Technical Specifications Specifications and FeaturesADSL Compliance Compliant with ADSL Standard • Full-rate ANSI T1.413 Issue 2 •
55 WDS repeater function support Firewall Built-in NAT firewallStateful Packet Inspection (SPI) DoS attack prevention including IP Spoofing, L
56 WAN (DSL) ADSL Port with RJ-11 connector USB USB 2.0 portConsole PS2 portAntenna 3 * 2 dBi external R-SMA Antenna Wireless IEEE802.11n (draf
57 APPENDIX B: Compatibility List Following is possible to find a list of compatible USB 3G modem to use with the WebShare 3G 244WN. Brand Model S
58 NOVATEL MC950D NOVATEL MC930D NOVATEL MC990D BandRich Bandluxe C100 Alcatel OT-X020 C-Motech D50 Telstra USB3-8521 Option GlobeSurfer i
Via Pelizza da Volpedo, 59 Cinisello Balsamo – MI – Italy info@atlan
6 Dichiarazione di Conformità Sintetica Con la presente Sidin SpA dichiara che questo apparato è conforme ai requisiti essenziali ed alle altre
7 Il suo contributo nella raccolta differenziata dei rifiuti di apparecchiature elettriche ed elettroniche è essenziale per il raggiungimento di tut
8 Questo manuale è inteso come una guida rapida, pertanto per ulteriori dettagli sulla configurazione fare riferimento al manuale esteso contenuto n
9 1.2 I LED frontali LED SIGNIFICATO Power • Acceso verde durante il corretto funzionamento. • Acceso rosso durante la fase di POST (Power On
Commenti su questo manuale